MESSAGE
| DATE | 2015-03-08 |
| FROM | Ruben Safir
|
| SUBJECT | Re: [NYLXS - HANGOUT] cable crimping
|
Robert, do you have the artcile for me, PLEASE
Ruben
On Wed, Mar 04, 2015 at 10:20:02AM -0500, Paul Robert Marino wrote:
>
> Here is the new one I was talking about warning I haven't tried it yet
> but it seams like a good idea.
> http://www.cables.com/Products/100004.aspx
> you will see at the bottom of the page the special endings they use.
> The down side is the endings are more expensive but 1 bulk pack is
> probably more than you will ever use.
> The way I always handle the sequence is to compare it to a pre-made
> cable I never remember the sequence off the top of my head. Remember
> the sequence is different on each side.
>
>
>
>
> On Wed, Mar 4, 2015 at 9:12 AM, wrote:
> > I always use the cheap $5 crimper because I find once you practice with it a little the more expensive ones ???cause bad crimps more often.
> >
> > How much cable crimping are we talking about? It's a tedious task especially with cat 6. So I usually order them from cyberguys or cables.com nowadays because are cheap and verified with better test tools than I have at home???.
> >
> > It's really not to hard it just takes practice and a little effort to initially straiten the wires. I always strip the casing back more that I need to??? them clip the wires to the correct length after I've straiten sequenced and aligned them. The next important thing is to make sure that all of the wires go all the way to the end of the connector before you crimp it. Then always test it when you are done.
> >
> >
> > There are also some new crimping tool and endings I seen recently for home ???use which allow you to run the wires completely through the ending then clip off the excess when you crimp them.
> > These are probably not good for professional use due to the increased risk of the ends of the wires corrosion in 5 to 10 years but should be just fine for use at home.
> >
> >
> >
> > Sent from my BlackBerry 10 smartphone.
> > Original Message
> > From: Rick Moen
> > Sent: Tuesday, March 3, 2015 18:00
> > To: hangout-at-nylxs.com
> > Reply To: hangout-at-nylxs.com
> > Subject: Re: [NYLXS - HANGOUT] cable crimping
> >
> >
> > Quoting Ruben Safir (mrbrklyn-at-panix.com):
> >
> >> Paul, I need you to come to the house and crimp a cable for me. Infact,
> >> you can show me how to do it.
> >
> > After he shows you classic TIA 568A and 568B cable wiring
> > configurations, buy yourself an ideal Industries Crimpmaster.
> > http://www.amazon.com/Ideal-30-522-Crimpmaster????-Crimper/dp/B0009WABT4
> >
> > You can also buy die sets for them, in case you want to do things other
> > than RJ-45, such as RJ-11 (telco) and other things.
> >
> > Don't settle for any lesser crimping tool. There's a lot of them out
> > there that just suck.
> >
> >
> > Also: Get a big bag of RJ-45 ends and practice with them -- because it
> > takes some practice before you stop making dud cables. Once you've
> > gotten the knack, you can then turn out reliable ethernet cables with no
> > problem.
> >
> > Also#2: If buying new ethernet cable, spring for CAT6E. (Yes, even
> > though officially no such spec exists, it nonetheless de-facto does.)
> > I make no apologies over my still working on using up the 1000' spool of
> > CAT5 I bought in 1997, but wouldn't _think_ of buying more of it.
> >
> >
|
|
